Thermal analysis of glasses for proecological applications

Thermal behaviour and biochemical activity of potassium-silicate-phosphate glasses modified by addition of Ca, Mg, acting as ecological fertilisers of controlled release rate of the nutrients for plants were studied. It has been found that the biochemical activity of silicate-phosphate glasses depends on the nature and the number of components forming the glassy framework and is related to the thermal stability of glass demonstrated by the formation of new compounds during the process of crystallisation. It is proved that these seemingly different properties are determined by the same parameters which are the strengths bonds of glass network-formers and modifiers as well as their chemical affinity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Interaction of water with the regenerated cellulose membrane studied by DSC

One to three endothermal peaks atributted to melting of bulk and interfacial water were observed by DSC in the regenerated cellulose — water system. The profiles of thermal effects depend on water content, time of conditioning, film pretreatment and the conditions applied during the preceding freezing-thawing cycles. The occurrence might be deduced of melting-crystallisation processes. A large amount of non-freezable strongly bounded water was also detected. Although cellulose absorbs water quickly after immersion, the structural changes consisting on ordering of polymer fraction occur during further conditioning due to increase in strength of water binding. Using the membranes in the separation module at 90°C causes weakening of these bonds. Differences between interaction of particular cellulose films with water can be detected during the first, the second and the third heating. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of the polyethylene confinement and topology on its crystallisation within semicrystalline ABC triblock copolymers

The isothermal crystallisation behaviour of the polyethylene block within polystyrene-b-polyethylene-b-poly(ε-caprolactone), SEC, triblock copolymers was studied by differential scanning calorimetry. The morphology was observed by transmission electron microscopy. Melting scans after isothermal crystallisation performed at different times were employed to determine the crystallisation kinetics one step at a time (“isothermal step crystallisation”). Double melting endotherms were observed after isothermal crystallisation and they were interpreted as a result of the melting of two lamellar populations. These arise from the intrinsic short chain branching distribution within the hydrogenated polybutadiene chains that conform the PE blocks and from their location within the copolymer microdomains. The Hoffman-Weeks procedure failed to yield reasonable values for the equilibrium melting point of the PE blocks as a result of the distribution of linear sequences present in these blocks. The results indicate that as the degree of PE confinement increases the Avrami index decreases to values that are even lower than 1, a result that can be explained by the nature of the homogeneous nucleation process that is in between sporadic and instantaneous.     

Reversible Melting of Semi-Crystalline Polymers 2. Annealing Near to the Melting Point

Annealing experiments have been carried out at a few degrees below the melting point of different polyethylenes (LDPE, LLDPE, HDPE), of polypropylene (PP) and of Nylon-6. The heat capacities decrease during the annealing, within a 2-4 min time scale, to a lower value which corresponds to the extrapolated heat capacity values obtained for the cooling cycle when the polymer is cooled from the melt. Heat capacities in the heating cycle following the cooling cycle of PP, Nylon-6 and HDPE have the same value as during the cooling section. This is not the case for LDPE and LLDPE. Exothermic total heat flow in the cooling section following the annealing indicates that the crystallisation takes place during the cooling rather than during the annealing period. The total melting enthalpy measured before and after the annealing cycle is the same. The reversing heat flow shows an excellent fit to the change of the crystallinity measured by small angle scattering of synchrotron radiation during a heating cycle at temperatures below the melting peak. A coupled thermodynamic interaction of the crystalline and the amorphous phases is concluded from this study. This kind of interaction is possible at the lateral end of polymeric chains incorporated into the crystalline phase. This is an indication of the portion of tie molecules in the system, i.e. the portion of fringed micelle type of crystalline morphology with respect to that of folded chain lamellae. This revised version was published online in July 2006 with corrections to the Cover Date.     

Annealing of Polypropylene/Polyethylene Blends Near to the Melting Points in TMDSC

Annealing experiments have been carried out just below the melting temperature of both polyethylene (LLDPE) and polypropylene (PP) and their blends. The total melting enthalpy measured after the annealing cycle was greater by 10-15% with respect to the value having been measured before it. During the annealing period the heat capacity decreases to a lower value within the first 2-3 min. Heat capacities of PP (either in pure form or in the blends) measured during the heating cycle following the annealing cycle have the same value as during the cooling section. The heat capacities of the LLDPE in the heating cycle following the annealing were those of the preceding heating cycle. The total heat flows in the cooling section following the annealing cycle were greater than those in another cooling cycle at the same temperatures indicating that the crystallisation takes place during the cooling rather than during the annealing periods. The presence of LLDPE decreases the crystallisation temperature of PP. The presence of SEBS in the blend results in a greater crystallisation temperature than that of pure PP. The crystallisation temperature of LLDPE increases with increasing levels of PP. This revised version was published online in July 2006 with corrections to the Cover Date.     

Shear-induced nonisothermal crystallization of two grades of PLA

Shear-induced nonisothermal crystallization of two commercial polylactides (PLAs) differing in optical purity was studied. The molten polymers were sheared at selected temperatures (T_s) and subsequently cooled. The crystallization was followed by a light depolarization method, whereas the specimens were analysed ex-situ by DSC, 2D-WAXS and SEM after etching. It was found that the effect of shear, especially on the crystallinity developed during post-shearing cooling, intensified with a decrease of T_s from 160 to 146 ^°C, and with increasing shear rate and strain. Moreover, the effect of shear on PLA1.5 with d-lactide content of 1.5% was stronger than PLA2.8 with 2.8% of d-lactide, although maximum crystallinity of both polymers was practically the same. A decrease of cooling rate from 30 to 10 ^°C/min increased crystallinity of both PLAs, except for those shearing conditions which induced high crystallinity even during faster cooling. Although SEM examination revealed some row-nucleated forms, no significant crystal orientation was detected by 2D-WAXS, indicating that, under the experimental conditions, the shear induced predominantly point-like nuclei.     

Effect of the self-assembly of collagen on crystallisation of calcium carbonate in aqueous solution

In order to investigate how the self-assembly of organic matrix influences crystallisation and growth of inorganic minerals, we selected collagen as the matrix and conducted three experiments of crystallisation of CaCO₃ in different reaction systems: H₂O system, as-assembled collagen fibrils system and self-assembling of collagen system. It is found that (i) the self-assembly process of organic matrix had a remarkable effect on the morphology of inorganic minerals: CaCO₃ crystals formed in the as-assembled collagen fibrils system were global clusters and those formed in the self-assembling of collagen system appeared as interlaced networks and (ii) the organic matrix decided the polymorph of crystals: CaCO₃ crystals were calcite in the H₂O system and appeared vaterite in the collagen system. From this study, we can conclude that the self-assembly of collagen fibrils greatly affect the crystallisation and growth of CaCO₃. Such results are significant in understanding the mechanism of biomineralisation in calcified tissues in general, and useful in the synthesis of biominerals.

(a)?CaCO₃ formed in the as-assembled collagen fibrils system. (b)?CaCO₃ formed in the self-assembling of collagen monomer system.The TEM images of samples obtained in the as-assembled collagen fibrils and self-assembling of collagen monomer system, were observed, respectively. The result shows that crystals CaCO₃ formed in the as-assembled collagen fibrils system were global clusters; crystals CaCO₃ formed in the self-assembling of collagen monomer system appeared interlaced networks.     

Crystallisation of nematic liquid crystal mixtures

In this paper, we propose a method to accelerate the crystallisation of nematic liquid crystal mixtures based on crystallisation theory. This method is to hold a nematic liquid crystal sample at a temperature suitable for crystal growth after aging it at a temperature suitable for nucleation. After we specified these temperatures of a nematic liquid crystal mixture using differential scanning calorimetry, we demonstrate that the two-temperature aging method is effective for the crystallisation of other nematic liquid crystal mixtures in which the crystal-liquid crystal transition temperature has so far been undetectable.     

Scattering experiments on the structure of concentrated dispersions

 In this work the Couette cell is compared with a more recently constructed disk shear cell. There are distinct advantages of the disk over the Couette cell, in particular, when it comes to the determination of the intensity along certain Bragg rods. Received: 12 December 2000 Accepted: 31 January 2001     

Aggregation of fluorine-substituted pyridines

The influence of fluorine substituents on the crystallisation behaviour of pyridine was investigated by crystal structure determinations. The low melting compounds 2-fluoropyridine, 2,6-difluoropyridine and 2,4,6-trifluoropyridine were crystallised by in situ crystallisation directly on the single crystal X-ray diffractometer.